Before you start, make sure your treadmill is plugged in to the mains. 1. Press the "STOP" button. 2. Hold down the "STOP" button and insert the "SAFETY KEY". 3. The units being used are displayed in the bottom right corner:     UNIT MI   or  UNIT KM. 4. Press "+" to change the unit. 5. Press "STOP" to confirm the changes. 6. You can now use your treadmill.  

1- The Bluetooth symbol lights up and indicates that a tablet or smartphone is connected to the console. This only works with the “Domyos Econnected” app for IOS and Android.     Econnected FAQs: https://support.decathlon.fr/support/application-e-connected-tp_1079 2- The USB port is only there to keep your tablet or smartphone charged when using your treadmill. 3- The jack socket is only there for connecting your MP3 player, tablet or smartphone to your console.

To see how far and how long you've run since starting to use your treadmill, remove the safety key and press "STOP" + "-" simultaneously then insert the safety key. Press the START button 7 times to show the total distance run on the speed display, or press the START button 9 times to show the total amount of time run on the speed display.

1. Check that the power cord is plugged into a working mains socket (to check if the wall socket is working, plugin a lamp or other electrical device).2. Check that the other end of the power cord is connected to your treadmill.3. Check that the main switch near the power cord is set to I.4. Check that the safety key is pushed fully home in the console.

1. Shoes: => The noise you can hear could be the sound of your shoes on the running belt. To check that the noise isn't coming from your shoes, please see the video below   2. The screws are loose:  => Tighten all of the screws.   3. The running belt is wonky: => Select the "CENTRING THE RUNNING BELT" tab in the MAINTENANCE section.   4. The running belt is not lubricated: => Select the "RUNNING DECK LUBRICATION" tab in the MAINTENANCE section.

The running belt is slack => Select the "RUNNING BELT TENSION" tab in the MAINTENANCE section.  

1. If your treadmill is plugged in to an extension cable, unplug it and plug it directly into a wall socket. 2. The problem could be caused by the power cord. In this case, please see the FAQ on ""YOUR TREADMILL IS NOT SWITCHING ON""

1. To pick up your heart rate accurately, the distance between your heart rate monitor and the console should be no more than 80 cm. 2. To pick up your heart rate accurately, adjust the position of the belt so that the sensors are in contact with your skin. Moisten the sensors well before use. As the diagram shows, the sensors are the black rubber surfaces on either side of the central part. 3. There are also other things that may affect how well your heart rate is picked up, such as clothing that knocks against the belt or that is very static, a very hairy chest, and traces of dirt on the belt. 4. The display is blinking or not functioning normally The battery is probably low, so you will need to charge it.

Check that the icon on your treadmill's console is off.

You will need the Allen key (BTR) that came with your treadmill:  1. Start your treadmill at a low speed (4 km/h).        2. Insert the key into the screw on the side where the running belt is off-centre.        3. Turn it a quarter turn clockwise (wait 30 seconds between each quarter turn) until the belt is back in the correct position.

 

The running belt is a wearing part that becomes loose over time. Re-tighten it as soon it begins to go slack (sliding sensation, jerky motion).

 

1&2. Turn the two adjustment screws a half turn clockwise (repeat if necessary, but make sure you don't over-tighten the belt).

 

3. The belt is properly tightened if you can lift the edges 2 to 3 cm on each side.

It's important to do this regularly (every 200 hours of use) to keep your treadmill working as long as possible.  1 & 2. Simply spray twice underneath the running belt on the right and on the left.  3. Then set your treadmill off at 5 km/h for 5 minutes, without standing on it.

Regular maintenance is necessary to preserve the performance of your appliance and extend its service life. To get rid of any annoying noises coming from your treadmill, remember to:

                       Tighten the screws and bolts once a month.

                       Lubricate the running belt after 200 hours of use.

                       Place a standard floor mat (Domyos Training Mat) under your treadmill.

 

CLEANING AFTER EACH USE:

                      Turn off and unplug your treadmill.

                      Apply a small amount of gentle universal cleaner to a pure cotton cloth. Do not spray the cleaner directly onto the treadmill and do not use ammonia or acid cleaners.

                      Wipe the console and screens.

                      Remove any dust and stains on the ramps, uprights, footrests, frame and motor hood. Remember to also wipe the platform alongside the running belt. Do not clean under the running belt.

1. Check the motor and the drive belt every 600 hours of use or every 3600 km*2. Replace the running belt every 500 hours of use or every 3000 km*3. Replace the running deck every 700 hours of use or every 4200 km*4. Replace the rollers every 600 hours of use or after 3600 km*

 

*To know the accumulated hours or kilometres, refer to the FAQ "HOW TO SEE THE TOTAL DISTANCE AND TIME RUN ON YOUR TREADMILL" in the SETTING UP AND USING YOUR PRODUCT section