COMFORT RUN

Ref : 8371087

Year of commercialization: 2016

Designed for walking or running with the goal of keeping fit and building your cardio and muscular abilities.

The Comfort Run is ideal for walking and running, in the comfort of your home, at speeds of up to 16 km/h. Our customers especially like its level of comfort, ease of assembly, and ease of use.

PRODUCT BENEFITS : 

VERSATILITY : Max speed: 16 km/h. Power incline from 0 to 10%

USER COMFORT : Running deck 45 x 127 cm

COACHING : 16 programmes and 5 objectives: time, speed, distance, calories burnt, bpm

I HAVE A PROBLEM

Your equipment is properly assemblied but you're having some difficulties during its use? Discover all of our solutions here.
MY CONSOLE DOES NOT INDICATE THE RIGHT UNITS OF MEASUREMENT FOR THE DISTANCE

Before starting to work on it, make sure you have connected your treadmill to the mains.

1. Press the "STOP" button

2. While holding the "STOP" button pressed down, insert the "SAFETY KEY"

3. The display at lower right shows you the unit used:      E=MILES    RN=Km/H

4. Press "+" to change the units

5. Remove the "SAFETY KEY" to confirm the changes

6. You can use your treadmill 

MY TREADMILL WILL NOT SWITCH ON

1. Make sure the power cord is plugged into a wall socket in working order (to check if the wall socket is working, plug in a lamp or other electrical device).

2. Make sure the other end of the power cord is plugged into your treadmill.

3. Check that the main switch near the power cord is in position I.

4. Make sure the safety key is inserted in the console.  

 

 

MY TREADMILL IS NOISY

The running belt is off-centre => Select the "Centre running belt" tab

The running belt is not lubricated => Select the "Lubricate running belt" tab

The screws are loose => Tighten all the screws on the upright  

 

THE TREADMILL DOES NOT START + ENGINE NOISE AND TWO LINES FLASH ON THE CONSOLE

The treadmill is in calibration mode:

=> wait 2-3 minutes, and you will find that the belt goes up and down. After calibration, the console will light up.

 

 

WHEN I GET ON MY TREADMILL, THE SPEED SLOWS DOWN

The running belt is slack

=> Select the "tension running belt" tab

 

THE BELT INCLINE FACILITY DOES NOT WORK OR IS STUCK

The belt has not had time to calibrate the incline:

=> Turn off the treadmill, turn it back on and insert the safety key

=> Let the calibration cycle take its course. The belt will then go up to its maximum setting, then back down to zero. This may take several minutes      

How to make Process calibration in case of incline problem:

1. Push on stop & speed+ buttons in same time

2. Insert safety key when still pushing on buttons

3. Push on stop button 1 time and information on bottom picture will appear

4.  Push on inclin+ button and process calibration will start                                        

THE TREADMILL SWITCHES OFF WHEN IN USE

1. The treadmill is programmed to stop after 99 minutes of use. Press the on/off button to reset and restart the treadmill

2. Check the circuit breaker, located near the power cable. If it is in the OFF position,  wait 5 minutes, then switch to the RESET position.

3. Check that the power cable is plugged in.

4. Remove key from console. Reinsert key into console.    

CYLINDER ASSEMBLY
MISSING OR BROKEN PART
WHAT PROGRAMS ARE AVAILABLE ?
You can not solve the problems or to find your answer, we invit you to contact us

I MAINTAIN MY PRODUCT

Care and maintenance is important for the maintenance and longevity of your appliance. Please find further maintenance instructions here.
MAINTENANCE

Regular maintenance is necessary to maintain the performance of the machine and to extend the life of the product.

The following can help reduce treadmill noise:

 

        1. Tighten the screws and bolts once a month.

        2. Lubricate the running belt after 200 hours of use.

        3. Place a suitable floor mat (such as the Domyos Training Mat) under your treadmill.

 

 

Cleaning:

 

        1. Switch off and then unplug the treadmill.

        2. Apply a small amound of mild, multi-purpose cleaner, using a 100% cotton cloth. Do not spray directly onto the walking belt and do not use acid or ammonia-based cleaning products.

        3. Wipe the console and screens.

        4. Remove any dust and grime from the hand rails, uprights, foot rails, frame and motor hood. In addition, wipe the deck along the sides of the walking belt. Do not wipe under the walking belt.

ADJUSTING THE POSITION OF THE RUNNING BELT (CENTRING)

1. Locate the coloured indicators at the back of your treadmill. If they appear red, the band needs to be re-centred. This will enable you to protect the running belt and prevent the machine from stopping when you aren't expecting it to.

2. Turn your treadmill to 4 km/h (2.5 mph) and stand at the back of the machine.

3. If the belt has shifted towards the left: Turn the left adjustment screw through half a rotation, in a clockwise direction.

4. If the belt has shifted towards the right: Turn the right adjustment screw through half a rotation, in a clockwise direction.

5. Leave your treadmill running for the time it takes for the belt to move across (1 to 2 minutes) and repeat the operation if necessary.

Make sure, however, that you do not over-stretch the belt.

ADJUSTING THE TENSION IN THE RUNNING BELT

The running belt will be subjected to wear and tear and become less taut over time. Be sure to tighten it as soon as it starts to slip (a skidding sensation, with jerky changes of speed).

 

1&2. Turn the 2 adjustment screws through half a rotation, in a clockwise direction. Repeat this step if necessary but make sure you don't over-stretch the belt.

3. La bande est correctement tendue si vous pouvez soulever les bords de 2 à 3 cm de chaque côté.

LUBRICATING THE RUNNING BELT

It is imperative that you keep your treadmill well-lubricated, so as to limit the amount of friction between the running belt and the deck. No lubrication is necessary if traces of silicone are present on the inner side of the running belt or on the deck (and the surface is damp and slightly greasy).

If the belt and the deck are dry:

 

1. Switch off your treadmill and unplug it.

 

2. Lift up the sides of the running belt and coat the inner surface with silicone.*

 

3. Plug your treadmill in again.

 

4. Make the belt rotate at a speed of 4 km/h (2.5 mph), with no-one on it, for 10 to 20 seconds.

 

5. Your treadmill is ready for use!

 

* A single lubrication corresponds to a dose of between 5 and 10 ml of silicone.

Please note that if you use too much silicone, you could harm the proper functioning of your treadmill (risk of skidding).

When buying lubricants, consult your local DECATHLON store or go to www.domyos.com.

MANUAL

You need the instruction manual? Click here to download

OUR ENGAGEMENTS

DOMYOS guarantees this product under normal use conditions, 5 years for the structure, 2 for other parts and labour as from date of purchase, as shown on receipt.

TOP OF PAGE